Tablet—CLEAN ALUMINUM LITHOGRAPHIC
SHEETS
To consist of ***0 and/or ***0 series alloys,
to be free of paper, plastic, excessively inked sheets, and any
other contaminants.Minimum size of 3" (8 cm) in any
direction.
Tabloid—NEW, CLEAN ALUMINUM LITHOGRAPHIC
SHEETS
To consist of ***0 and/or ***0 series alloys,
uncoated, unpainted, to be free of paper, plastic, ink, and any
other contaminants. Minimum size of 3" (8 cm) in any
direction.
Taboo—MIXED LOW COPPER ALUMINUM CLIPPINGS AND
SOLIDS
Shall consist of new, clean, uncoated and
unpainted low copper aluminum scrap of two or more alloys with a
minimum thickness of 0.**5 inches (.*8 mm) and to be free of ***0
and ***0 series,
hair wire, wire screen, punchings less 1/2 inch
(1.*5 cm) diameter, dirt, and other non-metallic items. Grease and
oil not to total more than 1%.Variations to this specification
should be agreed upon prior to shipment between the buyer and
seller.
Taint/Tabor—CLEAN MIXED OLD ALLOY SHEET
ALUMINUM
Shall consist of clean old alloy aluminum sheet
of two or more alloys, free of foil, venetian blinds, castings,
hair wire, screen wire, food or beverage containers, radiator
shells, airplane sheet, bottle
caps, plastic, dirt, and other non-metallic
items. Oil and grease not to total more than 1%. Up to *0% Tale
permitted.
Take—NEW ALUMINUM CAN
STOCK
Shall consist of new low copper aluminum can
stock and clippings, clean, lithographed or not lithographed, and
coated with clear lacquer but free of lids with sealers, iron, dirt
and other foreign contamination.Oil not to exceed
1%.
Talc—POST-CONSUMER ALUMINUM CAN
SCRAP
Shall consist of old aluminum food and/or
beverage cans. The material is to be free of other scrap metals,
foil, tin cans, plastic bottles, paper, glass, and other
non-metallic items.Variations to this
specification should be agreed upon prior to
shipment between the buyer and seller.
Talcred—SHREDDED ALUMINUM USED BEVERAGE CAN
(UBC) SCRAP
Shall have a density of *2 to *7 pounds per
cubic foot (**3 to **3 kg/m3). Material should contain maximum 5%
fines less than 4 mesh (U.S. standard screen size) (6.*5 mm). Must
be magnetically separated material and free of steel, lead, bottle
caps, plastic cans and other plastics, glass, wood, dirt, grease,
trash, and other foreign substances. Any free lead is basis for
rejection. Any and all aluminum items, other than used beverage
cans, are not acceptable.Variations to this specification should be
agreed upon prior to shipment between the seller and
buyer.
Taldack—DENSIFIED ALUMINUM USED BEVERAGE CAN
(UBC) SCRAP
Shall have a biscuit density of *5 to *0 pounds
per cubic foot (**2 to **2 kg/m3). Each biscuit not to exceed *0
pounds (*7.2 kg). Nominal biscuit size range from *0" to *3" x
**1/4" (*5.4 x *3 x *6 cm) to *0" x *1/4" x 9" (*0.8 x *5.9 x *2.9
cm). Shall have banding slots in both directions to facilitate
bundle banding. All biscuits comprising a bundle must be of uniform
size. Size: Bundle range dimensions acceptable are *1" to *4" x *1"
(**4 to **2 cm) to *4" x *4" (**7 x **7 cm) to *6 (**2 cm) high.The
only acceptable tying method shall be as follows: Using minimum
5/8" (1.6 cm) wide by .**0" (.*5 cm) thick steel straps, the
bundles are to be banded with one vertical band per row and a
minimum of two firth (horizontal) bands per bundle. Use of skids
and/or support sheets of any material is not acceptable. Must be
magnetically separated material and free of steel, lead, bottle
caps, plastic cans and other plastic, glass, wood, dirt, grease,
trash, and other foreign substances. Any free lead is basis for
rejection.Any and all aluminum items, other than used beverage
cans, are not acceptable. Items not covered in the specifications,
including moisture, and any variations to this specification should
be agreed upon prior to shipment between the seller and
buyer.
Taldon—BALED ALUMINUM USED BEVERAGE CAN (UBC)
SCRAP
Shall have a minimum density of *4 pounds per
cubic foot (**5kg/m3), and a maximum density of *7 pounds per cubic
foot (**3kg/m3) for unflattened UBC and *2 pounds per cubic foot
(**3kg/m3) for flattened UBC. Size: Minimum *0 cubic feet (.*5 m3),
with bale range dimensions of *4" to *0" (*1 to **2 cm) by *0" to
*2" (*6 to **2 cm) by *0" to *4"(**2 to **3 cm). The only
acceptable tying method shall be as follows: four to six 5/8" (1.6
cm) x .**0"(5 mm) steel bands, or six to ten #*3 gauge steel wires
(aluminum bands or wires are acceptable in equivalent strength and
number).Use of skids and/or support sheets of any material is not
acceptable.Must be magnetically separated material and free of
steel, lead, bottle caps, plastic cans and other plastic, glass,
wood, dirt, grease, trash, and other foreign substances. Any free
lead is basis for rejection. Any and all aluminum items, other than
used beverage cans, are not acceptable.Variations to this
specification should be agreed upon prior to shipment between the
buyer and seller.
Taldork—BRIQUETUED ALUMINUM USED BEVERAGE CAN
(UBC) SCRAP
Shall have a briquette density of *0 pounds per
cubic foot (**0kg/m3) minimum. Nominal briquette size shall range
from *2" to *4" (*0.5 x *1 cm) x *2" to *4" (*0.5 x *1 cm) in
uniform profile with a variable length of 8" (*0.3 cm) minimum and
*8" (**2 cm) maximum. Briquettes shall be bundled or stacked on
skids and secured with a minimum of one vertical band per row and a
minimum of one girth band per horizontal layer. Briquettes not to
overhang pallet.Total package height shall be *8 (**2 cm) maximum.
Banding shall be at least 5/8" (1.6 cm) wide by .**0" (5 mm) thick
steel strapping or equivalent strength.The weight of any bundle
shall not exceed 4, **0 pounds (1.**4 mt). Material must be
magnetically separated and free of steel, plastic, glass, dirt and
all other foreign substances.Any and all aluminum items other than
UBC are unacceptable.
Any free lead is basis for rejection. Items not
covered in the specification, including moisture, and any
variations to this specification should be agreed upon prior to
shipment between the buyer and seller.
Tale—PAINTED SIDING
Shall consist of clean, low copper aluminum
siding scrap, painted one or two sides, free of plastic coating,
iron, dirt, corrosion, fiber, foam, or fiberglass backing or other
non-metallic items.
Talk—ALUMINUM COPPER
RADIATORS
Shall consist of clean aluminum and copper
radiators, and/or aluminum fins on copper tubing, free of brass
tubing, iron and other foreign contamination.
Tall—E.C. ALUMINUM
NODULES
Shall consist of clean E.C. aluminum, chopped
or shredded, free of screening, hair-wire, iron, copper, insulation
and other non-metallic items. Must be free of minus *0 mesh
material. Must contain *9.*5% aluminum content.
TALLY All ALUMINUM RADIATORS FROM
AUTOMOBILES
Shall consist of clean aluminum radiators and
or condensers. Should be free of all other radiator type
commodities such as Talk or Ocean, shall also be free of copper,
brass, iron, plastic, foam excessive oxidation and other foreign
contamination.
Talon—NEW PURE ALUMINUM WIRE AND
CABLE
Shall consist of new, clean, unalloyed aluminum
wire or cable free from hair wire, ACSR, wire screen, iron,
insulation and other nonmetallic items.
Tann—NEW MIXED ALUMINUM WIRE AND
CABLE
Shall consist of new, clean unalloyed aluminum
wire or cable which may contain up to *0% ***0 series wire and
cable free from hair wire, wire screen, iron, insulation and other
non-metallic items.
Taste—OLD PURE ALUMINUM WIRE AND
CABLE
Shall consist of old, unalloyed aluminum wire
and cable containing not over 1% free oxide or dirt and free from
hair wire, wire screen, iron, insulation and other non-metallic
items.
Tassel—OLD MIXED ALUMINUM WIRE AND
CABLE
Shall consist of old, unalloyed aluminum wire
and cable which may contain up to *0% ***0 series wire and cable
with not over 1% free oxide or dirt and free from hair wire, wire
screen, iron, insulation and other non-metallic
items.
Tarry A—CLEAN ALUMINUM
PISTONS
Shall consist of clean aluminum pistons to be
free from struts, bushings, shafts, iron rings and non-metallic
items. Oil and grease not to exceed 2%.
Tarry B—CLEAN ALUMINUM PISTONS WITH
STRUTS
Shall consist of clean whole aluminum pistons
with struts. Material is to be free from bushings, shafts, iron and
non-metallic items . Oil and grease not to exceed
2%.
Tarry C—IRONY ALUMINUM
PISTONS
Shall consist of aluminum pistons with
non-aluminum attachments to be sold on a recovery basis or by
special arrangement between buyer and seller.
Teens—SEGREGATED ALUMINUM BORINGS AND
TURNINGS
Shall consist of aluminum borings and turnings
of one specified alloy.Material should be free of oxidation, dirt,
free iron, stainless steel, magnesium, oil, flammable liquids,
moisture and other nonmetallic items. Fines should not exceed 3%
through a *0 mesh (U.S. standard) screen.
Telic—MIXED ALUMINUM BORINGS AND
TURNINGS
Shall consist of clean, uncorroded aluminum
borings and turnings of two or more alloys and subject to
deductions for fines in excess of 3% through a *0 mesh screen and
dirt, free iron, oil, moisture and all other non-metallic items.
Material containing iron in excess of *0% and/or free magnesium or
stainless steel or containing highly flammable cutting compounds
will not constitute good delivery.To avoid dispute, material should
be sold on basis of definite maximum zinc, tin and magnesium
content.
Tense—MIXED ALUMINUM
CASTINGS
Shall consist of all clean aluminum castings
which may contain auto and airplane castings but no ingots, and to
be free of iron, brass, dirt and other non-metallic items. Oil and
grease not to total more than 2%.
Tepid—AIRCRAFT SHEET
ALUMINUM
Should be sold on recovery basis or by special
arrangements with purchaser.
Terse—NEW ALUMINUM
FOIL
Shall consist of clean, new, pure, uncoated
***0 and/or ***0 and/or ***0 series alloy aluminum foil, free from
anodized foil, radar foil and chaff, paper, plastics, or any other
non-metallic items.
Hydraulically briquetted material and other
alloys by agreement between buyer and seller.
Tesla—POST CONSUMER ALUMINUM
FOIL
Shall consist of baled old household aluminum
foil and formed foil containers of uncoated ***0, ***0 and ***0
series aluminum alloy. Material may be anodized and contain a
maximum of 5% organic residue. Material must be free from radar
chaff foil, chemically etched foil, laminated foils, iron, paper,
plastic and other nonmetallic contaminants.
Tetra—NEW COATED ALUMINUM
FOIL
Shall consist of new aluminum foil coated or
laminated with ink, lacquers, paper, or plastic. Material shall be
clean, dry, free of loose plastic, PVC and other non-metallic
items. This foil is sold on a metal content basis or by sample as
agreed between buyer and seller.
Thigh—ALUMINUM
GRINDINGS
Should be sold on recovery basis or by special
arrangements with purchaser.
Thirl—ALUMINUM DROSSES, SPATTERS, SPILLINGS,
SKIMMINGS AND SWEEPINGS
Should be sold on recovery basis or by special
arrangements with purchaser.
Throb—SWEATED
ALUMINUM
Shall consist of aluminum scrap which has been
sweated or melted into a form or shape such as an ingot, sow or
slab for convenience in shipping; to be free from corrosion, dross
or any non-aluminum inclusions. Should be sold subject to sample or
analysis.
Tooth—SEGREGATED NEW ALUMINUM ALLOY CLIPPINGS
AND SOLIDS
Shall consist of new, clean, uncoated and
unpainted aluminum scrap of one specified aluminum alloy with a
minimum thickness of .**5" (.*8 mm) and to be free of hair wire,
wire screen, dirt and other non-metallic items. Oil and grease not
to total more than 1%. Also free from punchings less than 1/2"
(1.*7 cm) in size.
Tough—MIXED NEW ALUMINUM ALLOY CLIPPINGS AND
SOLIDS
Shall consist of new, clean, uncoated and
unpainted aluminum scrap of two or more alloys with a minimum
thickness of .**5" (.*8mm) and to be free of hair wire, wire
screen, dirt and other nonmetallic items. Oil and grease not to
total more than 1%. Also free from punchings less than 1/2" (1.*7
cm) in size.
Tread—SEGREGATED NEW ALUMINUM CASTINGS,
FORGINGS AND EXTRUSIONS
Shall consist of new, clean, uncoated aluminum
castings, forgings, and extrusions of one specified alloy only and
to be free from sawings, stainless steel, zinc, iron, dirt, oil,
grease and other nonmetallic items.
Troma ALUMINUM AUTO OR TRUCK
WHEELS
Shall consist of clean, single-piece, unplated
aluminum wheels of a single specified alloy, free of all inserts,
steel, wheel weights, valve stems, tires, grease and oil and other
non-metallic items.
Variations to this specification should be
agreed upon prior to shipment between the buyer and
seller.
Trump—ALUMINUM AUTO
CASTINGS
Shall consist of all clean automobile aluminum
castings of sufficient size to be readily identified and to be free
from iron, dirt, brass, bushings, and non-metallic items. Oil and
grease not to total
more than 2%.
Twang—INSULATED ALUMINUM WIRE
SCRAP
Shall consist of aluminum wire scrap with
various types of insulation.To be sold on a sample or recovery
basis, subject to arrangement between buyer and
seller.
Tweak—FRAGMENTIZER ALUMINUM SCRAP (from
Automobile Shredders)
Derived from either mechanical or hand
separation, the material must be dry and not contain more than 4%
maximum free zinc, 1% maximum free magnesium, and 1.5% maximum of
analytical iron. Not to contain more than a total 5% maximum of
nonmetallics, of which no more than 1% shall be rubber and
plastics.To be free of excessively oxidized material, air bag
canisters, or any sealed or pressurized items. Any variation to be
sold by special arrangement between buyer and
seller.
Twire—BURNT FRAGMENTIZER ALUMINUM SCRAP (from
Automomobile Shredders)
Incinerated or burned material must be dry and
not contain more than X% (% to be agreed upon by buyer and seller)
ash from incineration, 4% maximum free zinc, 1% maximum free
magnesium,
and 1.5% maximum of analytical iron. Not to
contain more than a total 5% maximum of non-metallics, of which no
more than 1% shall be rubber and plastics.To be free of excessively
oxidized material, air bag canisters, or any sealed pressurized
items.Any variation to be sold by special arrangement between buyer
and seller.
Twist—ALUMINUM AIRPLANE
CASTINGS
Shall consist of clean aluminum castings from
airplanes and to be free from iron, dirt, brass, bushings, and
non-metallic items. Oil and grease not to total more than
2%.
Twitch—FLOATED FRAGMENTIZER ALUMINUM SCRAP
(from Automobile Shredders)
Derived from wet or dry media separation
device, the material must be dry and not contain more than 1%
maximum free zinc, 1% maximum free magnesium, and 1% maximum of
analytical iron. Not to contain more than a total 2% maximum of
nonmetallics, of which no more than 1% shall be rubber and
plastics.To be free of excessively oxidized material, air bag
canisters, or any sealed or pressurized items. Any variation to be
sold by special arrangement between buyer and
seller.
