La description
Pure
Acrylate Sports Coating for Hard Court Surface
Â
DESCRIPTION:
Nalstane Pure Acrylate Sport Hard Court Surface
Systems provide a highly durable, all weather sporting surface with
excellent abrasion resistance and uniform texture.
Manufactured from selected premium **0% acrylic resins, light
stable oxide pigments and proven reinforcing powders assure maximum
U.V. resistance to provide years of non-fade life.
The specialized resins used in the production of Nalstane provide
excellent scuff resistance in both wet and dry conditions.
The Nalstane Pure Acrylate Sport Hard Court Surface Systems for
asphalt bases comprises two (2) applications of Filler Coat and at
least one (1) application of Nalstane Top Coat.
Ball bounce on Nalstane PA is completely true and ball speed can be
varied by the application technique of the qualified
contractor.
ADVANTAGES:
Early
water resistance. Dries rapidly. Excellent adhesion. Excellent
scuff resistance (in wet and dry). Provides positive traction. Is
easily cleaned. Remains flexible. Provides true ball bounce and
controlled ball speed.
TYPICAL USES:
Tennis
Courts, Basketball Courts, Outdoor Play Areas, Volleyball Courts,
Multi-purpose Sport Courts.
SURFACE PREPARATION:
NEW
ASPHALT SURFACES - A
tight, uniform and even surface is required to avoid the need for
additional applications of Filler Coat. New asphalt surfaces shall
be allowed to cure for a minimum of *0 days before the application
of the Nalstane System. The surface finish shall be thoroughly
cleaned to remove all loose dirt, dust, oil, grease, leaves and
other debris. The surface shall be flooded with water to check for
low areas. Minor depressions up to 3mm may be leveled using
undiluted Filler Coat applied by steel trowel/squeegee or a
combination of both. Deeper depressions and minor surface cracks
shall be filled with Nalstane M***0 blending with
concrete.
PREVIOUSLY COATED ASPHALT SURFACES
- Surface preparation requirements
are similar to those stated above for new asphalt. The surface
Shall be thoroughly cleaned and leveled. Existing cracks shall be
cleaned and filled with filler coat Nalstane M***0. Existing line
markings applied using an oil-based paint shall be
removed.
APPLICATION:
Do not
use Nalstane PA system when temperatures are either below 5°C or
above *5°C, or when rain is imminent. Sound surfaces require the
use of two (2) coats of Filler Coat and two (2) coat of Nalstane
Top Coat. Areas of excessive porosity should receive an additional
coat of undiluted Filler Coat applied by squeegee or trowel. In
general, unless a slower playing field for tennis is required, the
first coat is to be applied in a perpendicular (length wise)
direction to the playing net. The second coat is applied parallel
with the playing net with the finish coat perpendicular (length
wise). To create a slower playing field the reverse procedure is
applicable.
BASE
COATS – Mix primier A
and B by ratio 1:1, stirring 4mintes and then Dilute it with water
by ratio of 1 parts to 3 part of clean water and rolling onto
concrete substrate. This base coats is not necessary for asphalt
substrate.
SECOND
COAT (OR FILLER COAT) -
Dilute Filler Coat Nalstane M***0 in the ratio of 4 parts filler
coat to 1 part sand. Stir the mixture thoroughly before and during
the application procedure to provide a homogenous blend and avoid
settlement. Pour the mixture in 'wind rows' over the surface and
spread evenly with a wide flexible rubber squeegee, generally **0mm
to **0mm in width. Level off with a second squeegee. Note: In
situations where the asphalt base is unusually porous and
additional filling is required, it may be necessary to apply
additional coats of Nalstane M***0 neat without dilution. Any
subsequent squeegee lines must be rubbed smooth prior to the
application of the final Filler Coat.
TOP
COAT - It is important
that all ridges are leveled off prior to the application of the
finish coat and that the finish coat is true with an even texture.
Mix the Nalstane Surface coating in the ratio of 4:1 with fine
selected sands. Pour the mixture in 'wind rows' over the surface
and spread evenly with a wide flexible rubber squeegee, level off
with a wide firm bristle broom before coating starts to dry. Apply
a minimum of 2 coat, length wise of the court.
COVERAGE: (BASED ON UNDILUTED
MATERIAL)
Coverage will depend upon the texture of the base
surface to which the Nalstane M***0 Filler Coat is
applied.
Nalstane M***0
|
Â
|
1st
coat:
|
**3 sqm per
litre
|
2nd
coat:
|
**4 sqm per
litre
|
Nalstane Surface Coating
|
**4 sqm per
litre
|
DRYING TIMES:
In
general the first filler coat application will take longer to dry
because of the extra thickness of the product due to voids.
Allow approx. **1.5 hours at *5ºC. Additional coats average 0.5 - 1
hour at *5ºC.
Allow a minimum of 1 hour, depending on temperature, between
coats.
There is no maximum drying time limit between re-coats.
Playing time is generally *4 hours after completion, dependant on
good drying conditions.
Full hardness and abrasion resistance will take 4 *5 days under
good drying conditions.
LINE
MARKING:
Apply
Line***0 line paint by brush, roller or spray. Colours available
are white and yellow. Apply in two (2) coats by brush or roller or
one (1) coat by an appropriate spraying unit to achieve a total
coverage of approximately *0 lineal metres per litre for *0mm wide
lines.
COLOURRANGE:
Nalstane is available in nine (9) standard
weather resistant colours. Special colours are available on
request. Deep Green, Forest Green, Light Sage, Terracotta, Light
Terracotta, Mid Tan, Mid Blue, Blue Grey, Fawn.
PRECAUTION:
Store
in a cool place, never in the hot sun, keep material from freezing.
Clean all equipment with water, immediately after use. Do not allow
Nalstane PA coating to drip on adjacent surfaces. Immediately
remove drips with water as dried product is difficult to remove and
will create a blemish on the finished surface.
LIMITATIONS:
Although Nalstane PA coating has
excellent early water resistance, do not apply when rain is
imminent or temperatures are below 5°C or above
*5°C.Â
Pays: |
China |
N ° de modèle: |
PA-M200
|
Prix FOB: |
(Negotiable)
Obtenir le dernier prix
|
Localité: |
- |
Prix de commande minimale: |
- |
Commande minimale: |
100000 Square Meter |
Packaging Detail: |
Acrylic acid lacquer: 5gallom/drum 55galon/drum |
Heure de livraison: |
7-10days after receipt of payment |
Capacité de Fournir: |
- |
Payment Type: |
T/T, L/C, Western Union, Other |
Groupe de produits : |
- |