hydraulic butt fusion welding machine

La description

• 
   
   SHBD**0 pe pipe welding equipment up to **0mm ***-Application:
   
   PEpipes welding machine;
  HDPE pipes welding machine;
  PPpipes welding machine;
  PB pipes welding machine;
  PVDF pipes welding machine;
  any other plastic pipes available for welding... ...
  SHBD**0 pe pipe welding equipment up to **0mm ***-Further parameters:
   

  Model	SHBD**0	SHBD**0	SHBD**5
  Welding range(mm)	*3,*5,*0,**0, **5,**0,**0	**0,**5,**0,**0, **0,**0,**5,**0	**0,**0,**0,**5, **0,**0,**5
  Heating plate temperature	**0°C	**0°C	**0°C
  Heating plate surface temperature(******0°C)	±5°C
  Pressure adjustment range	**6.3MPa	**6.3MPa	**6.3MPa
  Cross-sectional area of the cylinder	**6mm2	***0mm2	***0mm2
  Working Voltage	**0V,*0Hz	**0V,*0Hz	**0V,*0Hz
  Heating plate power	1.0KW	2.1KW	3.1KW
  Cutter power	0.*5KW	1.*6KW	1.*6KW
  Hydraulic station power	0.*5KW	0.*5KW	0.*5KW
  Total Power	2.6KW	4.*1KW	5.*1KW

   
  SHBD**0 pe pipe welding equipment up to **0mm ***- Our advantages:
  
   
• SHBD**0 pe pipe welding equipment up to **0mm main electrical componentsare imported overseas, which are more reliable and stable, extend the life of welding machine and performance more efficiently.
•  
• SHBD**0 pe pipe welding equipment up to **0mmwill be spread a layer of oil, and then be wraped by plastic film, put into a wooden box at last. This type of packages is avoid getting rusty easily. 
•   SHBD**0 pe pipe welding equipment up to **0mm ***-Operation instruction:
   
• The od card which matches the pipes must be used. Stuck the pipe tightly then fix them on the rack.
• Open the ends of pipes,put in the milling cutter, and fix the milling cutter on the rack. Start the milling cutter, mover forward the cylinder,close the fixture and cut the ends. when it forms into thecontinuous chips, lower the pressure to zero firstly, then open the fixture and close the milling cutter at last.
• Put down the milling cutter, close the ends, and check up the pipe of the two ends. Check up the temperature of the heating plate. For the first welding, the temperature of the heating plate should be heated over the pre-heated temperature . Every time for welding, the heating plate must be cleaned.
• Put the heating plate with the suitable temperature on the rack, close the fixture, make the end meets the end meets the heating plate fully and set the system pressure.
• When the end raises uniformly and the height of the crimps meet the requirements, the heating time should be lowered at the same time.
• When it get to the endothermic time, open the fixture quickly and remove the heating plate.
• Close the fixture quickly, adjust the pressure uniformly in the specified time and write down the cooling time.The pressure should be kept until the ends cool down completely.
• When it gets to the cooling time, adjust the pressure to zero, open the fixture, and remove the welded pipe.
• ABOUT US:
   
  
   
• we are professional in the production of SHBD**0 pe pipe welding equipment up to **0mm . Any questions, you could tell me , because we the professors.
•  our price is the lowest in the same product, our quality is the highest in the same price . so our product is the highest cost-effective.
• we sell not only products but also our perfect service