Automatic Egg Incubators

La description

Automatic Incubator Applications: The equipment used for hatching chickens, ducks, geese, pigeons, quails and other rare birds and poultry. Technical parameters: Voltage: **0 V +/- *0% Current: *0 HZ Temperature range: *0 - *0 degree C Accuracy: +/- 0.1 degree C Humidity range: *0 - *0% Turning egg angle: *5 degree C One, The characteristics of the equipment: 1, High economic efficiency, as the main sources of heat to electricity, coal to add sources of heat, this machine can be used briquettes, briquettes, Meibing, charcoal, gas and other fuels, can also be used to replace the hot water method to maintain constant temperature. 2, Be not afraid of power failure: automatic control with power, monitored by people when power failure. After the blackout could be long-term normal operation. 3, Safe and reliable: The water in the heater is heated by the stove first, steam and hot water enter into the water plate through the pipe, stoves and machines are separate, there is not smell inside of the machine. The machines are installed with high temperature insulation nickel chrome plastic packets of fever for temperature. 4, The above layer of machine for incubating, the below layer of that for animals out. Two, The main technical indicators: 1. Temperature display range: 5 ~ *0 degree C 2. Temperature accuracy: +/- 0.1 degree C 3. Humidity display range :***9% RH 4. Humidity accuracy: +/- 5% RH 5. Output terminals: 7 Road (Excess-temperature, temperature control, low temperature, left turning eggs, right turning eggs, wet control, alarm) 6. Output current: temperature control, low temperature 6A, other 1A , 7. Turning eggs frequency: **9, the largest recorded. 8. Turning eggs cycle: 0.1 to *9.9 hours adjustable (pre-set at 1.5 hours) 9. Turning eggs time: 1 to **5 seconds adjustable (factory set at **0 seconds) *0. Ventilation time: ****9 minutes (adjustable, pre*0 hours, no ventilation) *1. Ventilators time: ****9 seconds (adjustable, factory set *0 seconds) *2. Measurement of lines: about 1.5 meters Three, The working conditions: 1. Voltage: AC **0 V ~ **0V, *0HZ 2. Relative Humidity: less than *5% 3. Ambient temperature: **0 degree C ~ *0 degree C Four, temperature and humidity settings, for example: If an incubator requires temperature *7.9 degree C ~ *8 degree C, humidity *5% ~ *0% RH. Click on, , the temperature screen will display PPP, when the humidity screen is off, loose the , temperature screen will display the three figures for the value of the original incubation temperature settings, if you want to change, cles, the max. temperature is *8 degree C. Then press the , the temperature screen will be off, humidity screen will display the three figures for the value of the original incubation humidity settings, if you want to change , click or to adjust the figures, the max. humidity is *0% RH. Then press SET for 1 second until FFF flash twice, which means the setting information be saved, then loose the , the machine will automatically return to normal working condition. Five, Arbitrary temperature and humidity settings, for example: Click Set , machine will show PPP, continue to hold down the , click to display P1 then loose the , the left shows three figures for over-temperature alarm. the machine will alarm when the temperature reaches this value. Click to adjust the figures show that the value you need. Then press Set , machine will display P2 then loose the . Shows three figures for over-temperature value, The fan will start when the temperature reaches the value. Click or to adjust the figures show that the value you need. Then press Set , machine will display P3 then loose the . Shows three figures for the temperature control on the limit. The machine will stop heating when the temperature reaches the value. Click to adjust the figures show that the value you need. Then press Set , machine shows P4. Shows three figures for temperature control under the limit. The machine will start heating when the temperature reaches the value. Click or to adjust the figures show that the value you need. Then press , machine shows P5. Shows three figures for the value of ***** machine will start heating of the backup heater when the temperature droppes to the value. Click or to adjust the figures show that the value you need. Then press Set , machine shows P6. Shows three figures for under temperature ***** machine will alarm when temperature reaches the value. Click or to adjust the figures show that the value you need. Then press Set , machine shows P7. Shows two figures for exceeding humidity ***** machine will alarm when humidity reaches the value. Click or to adjust the figures show that the value you need. Then press Set , machine shows P8. Shows two figures for stopping humidifying. The machine will stop humidifying when the humidity are more than the value. Click or to adjust the figures show that the value you need. Then press Set , machine shows P9. Shows two figures for starting humidifying. The machine will start humidifying when the humidity is less than the value. Click or to adjust the figures show that the value you need. Then press Set , machine shows Pa. Shows two figures for low humidity alarm. The machine will alarm when the humidity reaches the value. Click or to adjust the figures show that the value you need. Arbitrary temperature and humidity has been set up, and then press the Set and keep for one second until FFF flashing twice on the screen, which means the setting information is saved, then the machine automatically returns to normal working condition. Six, The settings for turning eggs: At the same time, press the Set and Reduce” keys, the machine will display PPP, continue to hold down the , click to display F1 then loose the . The left shows three figures for the total number of eggs up, which will be lost for power failure, the number will start from zero when get the power again. Click , the total number of eggs up will be cleared. Then press Set , when display F2 then loose the , show 3 figures which is turning eggs cycle time (unit:hour), factory set 1.5 hours. Click or to adjust the figures. Turning eggs cycle time 0 means not turning eggs. Then press Set , when display F3 then loose the , show 3 figures which is turning eggs time (unit:second), factory set **0 seconds. Click or to adjust the figures. Then press Set , when display F4 then loose the , show 3 figures which is ventilation cycle time (unit:hour), factory set 0 hour. Click or to adjust the figures. Ventilation cycle time 0 means: do not ventilate. Then press Set , when display F5 then loose the , show 3 figures which is ventilation time(unit:second), factory set *0 seconds. Click or to adjust the figures. Seven, Manual turning eggs: Directly press on the key can turn eggs slightly, the turning direction will be determined by the computer automatically. Eight, The function of temperature and humidity calibration: Hold down key to start the machine , Display EEE means enter into the calibration function, and the temperature will display, click or to adjust the figures to match the standard temperature. Then press SET key, the temperature display will be off, and the humidity display will be on, click or to adjust the figures to match the standard humidity. Then press SET key for 1 second until FFF flash twice, which means the setting information be saved, then loose the , the machine will automatically return to normal working condition. The relative humidity can be adjusted with small screws-driver to whirl the POT in the small hole of the humidity sensor. Nine, Self-test function: Can not self-test with load. Hold down key to start machine, seven output relayes pull in and release in turn. Click can return to normal working condition. Ten, Rapid return to the status of the original factory settings Hold down the SET key to start the machine until FFF flasheing, setting restore the original status, the temperature is *8 degree C, humidity *0% RH, turn eggs cycle 1.5 hour, turn eggs time **0 seconds, ventilation time 2 hours, ventilation time 0 Seconds (stop ventilators). Then automatically return to normal work.