❯

BOOK A CALL

Book Call On Your Favorite Time

I'm a Buyer I'm a Supplier

By Signing Up. I agree to TradeKey.com Terms of Use, Privacy Policy, IPR and receive emails related to our services

high voltage 100watt CO2 lase rpower source for CO2 laser engraving or cutting equipment

FOB Price

Obtenir le dernier prix

109 ~ 118 / Piece ( Negotiable )

Minimum Order

Localit�:

Prix de commande minimale:

Commande minimale:

50 Piece

Packaging Detail:

carton and foam

Delivery Time:

3-4 working days after payment received

Supplying Ability:

4000 Piece per Month

Payment Type:

L/C, D/A, D/P, Western Union

Contacter maintenant

Jinan Ruby Laser Technology Co., Ltd

China

Membre gratuit

Personne Ã contacter william

Jinan, Shandong

Contacter maintenant

Description

ZR***0W CO2 POWER SOURCES
Feature
1. The **0w laser power supply unit can match with EFR,SPT,Yongli, Weiju and other brands\' ******5cm sealed glass type CO2 laser lamp. The external LCD laser power supply unit selects zero-current half-bridge soft-switch circuit to make sure the air cooling laser power supply unit has high efficiency and fast response speed.
2.The air cooling laser power supply unit\'s control interface is applicable to high/low level signal. TTL level is to control the on/off of the laser power with a protective switch to check water-flow and ventilation.
3.This air cooling laser power supply unit has RED TEST button to easily figure out CO2 power supplies or CO2 laser tube\'s failure. It is very easy and simple to remove trouble.
4.Each external LCD laser power supply unit before selling will go through the aging check:
(1) sustain *0 hours at temperature *0 Degrees Celsius under full-load condition;
(2) **0 times on/off check for 7 seconds.
5. Input analog signal(0~5V) or PWM is selected to control the output laser power on this **0w laser power supply unit.
6. The **0w laser power supply unit has H/L/P/G/IN/5V control signal interfaceï¼ŒThe upper cover and bottom shell are aluminum Casing is made of galvanized sheet.
7.The **0w laser power supply unit is well grounded, which can ensure the safety of operators. At the same time, the air cooling laser power supply unit also has an open circuit protection function, which allows the external LCD laser power supply unit to work for a short time in the open circuit state.
8.This**0w laser power supply unit is equipped with two cooling fans. Better heat dissipation can protect the internal electronic components of this power supply.
9.This laser engraving power supply unit can use an external LCD module. It can display common fault codes, output current and working status. It is helpful for operators to understand the working state of **0w laser power supply unit and solve problems quickly. In addition, the output current can also be changed by the rotating potentiometer of the LCD module.
Specification

lnput	Input voltage			AC*0V±0% (AC**0V specified while order)
	AC frequency			7~*0HZ
	Maximum input power			**0W
	Maximum input current			3.5A
Output	Maximum output voltage			*5KV
	Maximum output current			*3mA (depending on the laser tubes of different manufacturers)
Efficiency				More than *0% (Full load)
Response speed				Not more than 1ms
Control lnterace				TTL multilevel switching control,effective level can be high and low selection (see control wining diagram)
Insulation		lnput-output		AC **0V 1 minutes not more than 0mA
		lnput-shell		AC **0V 1 minutes not more than0mA
		Output-shell		Connection
Open Circuit Protection				Can be short circuit (requires a good grounding shell,while avoiding the positive electrode and the shell between the arc)
Environmental Requested			Working temperature	*0â„ƒ~0â„ƒ
			Storage of temperature	*0â„ƒ~5â„ƒ
			Relative Humidity	Maximum *5%RH (non-condensing)
			Altitude	0,0 feet of work 0,0 feet of storage,dose not work
Cooling methods				Forced air cooling (fan cooling)
Dimensions (LxWxH)				5mmx5mmx**2mm

*1.ZR***0WA CO2 LASER POWER SUPPLY
Feature
1. The air cooling CO2 power supply has open circuit function, a good grounding in the case of protection, the **0watt CO2 power supply has short-term work in the open state, so to avoid the laser tube burst due to the damage caused by air cooling CO2 power supply, thereby enhancing black color power supply of life.
2.This **0watt CO2 power supply uses two Taiwan cooling fans to dissipate heat for the power supply. Its heat dissipation function is better than other brands laser power supply, which can prolong the service life.
3. The green signal block CO2 power supply uses PWM or **5V singal for laser power control. The H/L/P/G/I

high voltage 100watt CO2 lase rpower source for CO2 laser engraving or cutting equipment

Jinan Ruby Laser Technology Co., Ltd

Description

Send a direct inquiry to this supplier

To:

Je veux savoir:

high voltage 100watt CO2 lase rpower source for CO2 laser engraving or cutting equipment

Jinan Ruby Laser Technology Co., Ltd

Description

Send a direct inquiry to this supplier

To:

Je veux savoir:

Get Verified Buyers & Suppliers

Avail Free Consultation