Description

Features
● Constant Current output						● Typical lifetime ≥ 50000 hours
● Plastic case with terminal，Class II.						● 100% full load bur-in test
● Built-in EMI filter with tiny ripple,flicker-free						● Protection: Short circuit/Over current/Over voltage/Over load
● High performace and reliability						● 3 years warranty
Specifications								CE  RoHS  SELV
Model	Power	Input Voltage	Output Voltage	Output Current	Effi	PF	IP	Dimension	Weight	Warranty
NC-12300-LCT6	3-12W	180-265Vac	30-42Vdc	110mA	83%	≥0.9	IP20	88*38*21mm	50g	3 years
			30-42Vdc	150mA
			15-23Vdc	250mA
			15-30Vdc	300mA
			24-42Vdc	300mA
NC-18450-LCT6	12-18W	180-265Vac	30-42Vdc	250mA	85%	≥0.9	IP20	100*43*21mm	80g	3 years
			40-55Vdc	300mA
			30-42Vdc	350mA
			30-42Vdc	450mA
NC-28700-LCT6	20-28W	180-265Vac	56-80Vdc	300mA	86%	≥0.9	IP20	130*43*21mm	120g	3 years
			30-42Vdc	450mA
			30-42Vdc	500mA
			30-42Vdc	600mA
			30-42Vdc	700mA
NC-481000-LCT6	30-48W	180-265Vac	50-72Vdc	600mA	88%	≥0.9	IP20	140*47*29mm	180g	3 years
			30-42Vdc	800mA
			30-42Vdc	900mA
			30-42Vdc	1000mA
NC-721500-LCT6	50-72W	180-265Vac	50-72Vdc	900mA	88%	≥0.9	IP20	155*53*30mm	250g	3 years
			30-42Vdc	1000mA
			30-42Vdc	1200mA
			30-42Vdc	1500mA
　
Characteristics	Frequency			50/60Hz	　	　	　	　	　	　
	Current tolerance			±5%	　	　	　	　	　	　
	Max Load			＜80%	　	　	　	　	　	　
	Leakage current((mA )			< 0.5mA / 230VAC		　	　	　	　	　
	Ripple&noise			< 650mVP-P	　	　	　	　	　	　
	hold-up/start-up time time			100ms, 30ms,20ms/ 230VAC			　	　	　	　
	Leakage current((mA )			< 0.5mA / 230VAC		　	　	　	　	　
Protection	Over current			above 108%-116%,power limiting, recovers automatically after fault removed						　
	Over voltage			switch off, recovers automatically after fault removed				　	　	　
	Short circuit			hiccup mode,recovers automatically after fault removed					　	　
Environment	Operating Temperature			-25℃~~+45℃		　	　	　	　	　
	Storage Temperature			-30℃~~+80℃		　	　	　	　	　
	Humidity			20~~95%	　	　	　	　	　	　
Security	LVD			2014/35/EU,EN61347-1:2015，EN61347-2-13:2014				　	　	　
	EMC			2014/30/EU,EN55015:2013+A1:2015, EN61547:2009,EN61000-3-2,EN61000-3-3:2013						　
	Voltage Insulation/Resistance			I/P-O/P:3.75KVAC,I/P-O/P:>100M Ohms/500VDC/28℃/65% RH					　	　
	Classification of Installation and Use			Class II	　	　	　	　	　	　
Note	◊ All parameters NOT specially mentioned are measured at 240VAC input, max rated load and 25℃ of ambient temperature
	◊ Ripple & Noise are measured at 20MHz of bandwidth by using a 300mm twisted pair-wire terminated with a 0.1uF & 47 uF parallel capacitor.
	◊ The driver is considered as a component to be operated in combination with equipment,since performance will be affected by the complete installation.
	◊ Good heat dissipation will prolong the working life of the driver.Please ensure good ventilation.
	◊ Please check if the output voltage of any LED lights used comply with the working voltage of the product.
	◊ Be ware of high power pressure may caused by short circut when installing metal casing products.
	◊ Please ensure all wires connections and polarities are correct before appling power to avoid any damages to LED Lights.
	◊ The product shall be installed and serviced by a qualified person.
	◊ Please contact supplier if a fault occurs.