La description
Automatic Banner Welding
Machine
Â
 APPLICATION
 The automatic welding machine is designed to weld plastic
materials. The automatic welding machine can weld advertising
inkjet fabric, inkjet cloth, light box cloth, thick PVC cloth,
mesh cloth, tarpaulin and other PVC, PE, DHPE, LDPE, EVA, Pp
plastic materials that can be hot melted. It is small, light and
easy to operate. It is equipped with temperature feedback sensor.
The sensor can always monitoring the temperature of the outlet to
keep a constant temperature. It uses advanced PID control
technology, and adjust the power to make the temperature more
constant automatically，the fluctuation is within 1 degrees.
This function can make the welding result stronger. It also can
avoid leakage. This machine is more suited to fast welding of
large roofs
Sequence of operation
1. First, make the picture smooth and tight, take jointer to
accurate （about **4cm）, fixed edges with tape or glue on the
ground.
2. Open the power, turning handle to left to keep hot air nozzle
and the rubber tire is on the straight line. Then turn the right
black knob to adjust the speed, generally marked on the knob
points to the location between 2 from 4.After setup, turning the
handle to right until the hot air out of the ground.
3. Set the temperature degree. Open temperature switch, And turn
the golden knob until it clicks and then follow the to the
end.â–²for up â–¼for down, set the desired temperature according
to thickness of picture。In general, the temperature is between
******0℃，Or taking some picture material to aligned nozzle,
If it can be melted immediately, This temperature is the one you
need and to set.
4. In the welding process, if printing material is burnt, the
first thing to slow down the speed or low the temperature，This
can avoid to  burnt picture material，but do not increase
speed rapidly, otherwise the machine will  run  too
fast to make it go straightly，this will cause the picture can
not be spliced ​​and damage the picture.
5. Before using, please find the proper temperature and speed
according to your printing material. If the speed is too slow it
could burn the picture, while too fast to welding strong.
Therefore, It is very important that the temperature and speed
are good match.
6. After welding, turning the handle to right to keep hot air gun
from picture completely，then turn off the temperature
switch(Left the gold knob until it make a voice of clicks)。No
lugging  the power cord and turning the power off
directly，to avoid heat damage to the hot air gun。After
temperature of the machine must be reduced to below *0 ℃,you
can plug the power or main switch.
7. Dont use it in rainy day，the workplace should be dry, flat
and safety of fire。The machine should have technical person to
operate， it is forbid that someone use it without specific
knowledge. Working voltage：**0V—**0V. Strictly prohibited
without permission disassemble，you should be responsible the
result yourself.
 You mustnt turn off the machine until the welding machine
will completely cool down in a few minutes. Then pull out the
plug.
Preparation before using the machine
1. You should adjust the temperature and speed according to the
thickness of your materials.
2. Fix the cloth on the smooth ground to make sure the best
result.
Maintain
1. Clean the nozzle with copper brush.
2. Clean the air inlet with soft bristle brush.
3. Check the power cord and plugs to avoid any mechanical
damage.  Â
Â
| Pays: |
China |
| N ° de modèle: |
LD-3000A
|
| Prix FOB: |
358 ~ 420 / Set ( Negotiable ) (Negotiable)
Obtenir le dernier prix
|
| Localité: |
- |
| Prix de commande minimale: |
358 per Set |
| Commande minimale: |
1 Set |
| Packaging Detail: |
carton |
| Heure de livraison: |
1-3 working days after check youe payment |
| Capacité de Fournir: |
999 Set per Month |
| Payment Type: |
T/T, L/C, D/A, D/P, Western Union, Money Gram |
| Groupe de produits : |
Welder machine
|
