WOYO PDR-007 Paintless Dent Repair Heat Induction

La description

WOYO PDR***7 Paintless Dent Repair Heat Induction

WOYO paintless dent repair tool is a vehicle specifically for small and medium-sized dent repair.

1.Simple to operate, easy to use, low cost of learning.

2. rapid repair, to the same depression area, *0 times faster than traditional repair method.

Fast delivery to the owner, improve workshop utilization rate, rapid recovery of investment

3. The two operating modes adapted to different requirements

(1)Time mode: under **0% power, 0.5 seconds –4 seconds, 7 file time setting, assess the size of the depression area, match the appropriate operating time by time gear, avoid poor time control to cause secondary damage.

(2) Power mode: *0%***0%  5 power settings, assess the size of the depression area, match the power shift with the 

appropriate power from small to large, realize the fast repair.

4. The high precision control, *5% imported chip equipment components, quality guarantee, stable and secure.

5. Large screen digital display, accurate control, real-time monitor.

Model: PDR—**7
Input: Voltage **0—**0V    
Frequency:*0Hz         
Fuse:*0A
Output: Peak Voltage **0V    
Frequency:*0—*5KHz    
Peak Power ≈ **0W

Packing List：

PDR Main*1
Main Cable*1
Power Cable*1
Repair Pen*3
Restoration Switch*1
One-year warranty


Manual

Before using this device, you must read the instructions. If the instructions are not followed
carefully, the operator could suffer injury, the device could be damaged, or the car being
treated might be damaged.

Before-use warning (MUST READ)
1. Not suitable for operation by those with pacemakers or artificial limbs with metal parts.
2. Before using this device, you must wear a safety mask, safety gloves, and safety clothing to
avoid being burned during use.
3. Operators must not have any metal objects on their person during operation, including but not
limited to watches, cuff links, keys, belt buckles, coins, or zippers.
4. This device cannot be operated in areas with conductive particulate matter, areas used for
applying paint, areas housing or handling chemical fuels, areas of high temperature, and areas of
high humidity.
5. Once the device is powered on, flammable objects must be kept away from the device.
6. Before you power on the device, make sure that you have a fire extinguisher on hand in case
any misoperation causes a fire.
7. Do not use this device in the vicinity of safety airbags.
8. Once the device is powered, there must be personnel on site to watch over the device. When the
device is not in use, unplug the device's power cable.
9. This device should be stored at temperatures between 0 and *0 celsius. When transporting the
device, avoid vibrations or shocks.

Important warnings for use (MUST READ)
1. While the restoration head is restoring a damaged car body, the temperatures of both the
restoration head and the body will rapidly increase. Do not touch either the restoration head or the
car body before they have had time to cool down.
2. While the restoration head is in the process of restoration, the temperatures of both the
restoration head and the damaged area will rapidly increase. Using the restoration head on one
area for too long may increase temperatures to the point of damaging the car's paint job (it is
recommended that every **1.5 seconds, the operator wipes down the damaged area with a wet rag
in order to keep the temperature manageable).
3. During the restoration process, the temperatures of both the restoration head and the damaged
area will rapidly increase and the body of the car will immediately become softer. During restoration,
make sure the restoration head is not applying pressure to the car, otherwise the restoration
process itself might further dent the car.
4.The "Time/effect Dial" intensity can be set between *0% and **0%. This is the strength that the
device runs at. Press the "Work" to activate the device. Let go of it and the device will stop.
5.Connect the "Extension Cable" to the device's Quick Connect head and the Restoration Head's
Quick Connection head, and the device is ready to use.
6. After work is complete, set the "Time/effect Dial" to "OFF", and after ***0 minutes, set the "ON/
 OFF Switch" to "OFF" as well. Give the device time to cool down, and then remove the "**0V
 Power Cable". Every time you use the device, repeat the steps above for a safe and effective
experience.

Dent repair method
Car body dent diagram

First, according to the size of the dent and the color of the paint, set the work time and intensity
of the Paint Damage-Free Dent Restorer. Typical use would see the "Time/effect Dial" set to 0.*-
1 second(s). Grip the restoration head and press the "Work" , and begin moving around
the dented area. First trace around "area 1", moving in to "area 4" as you add heat. Wait for
cool down. Then, begin at "area 2" and move towards "area 4" as you add heat. Wait for cool down.
Then, begin at "area 3" and move towards "area 4" as you add heat. Wait for cooldown. Finally,
continually add heat in "area 4", then wait for cooldown. The repair process should be complete.
(Some areas might require repeated applications of heat or repetitions of the above processes)
During the repair process, the operator MUST take note not to work in one area for more than
1 second. It is recommended that an operator applies compressed air or a wet rag to work areas
to prevent overheating. During the restoration process, great amounts of heat will be created,
causing the metal of the car to soften. Do not apply downwards pressure while restoring, or the
dent will just become larger. During the restoration process, the operator MUST be mindful of the
surface temperature of the car. If the heat gets too high, it will ignite the paint on the car's surface,
causing greater damage. We suggest the operator first practices on the piston cap of an unused
engine or an abandoned car, this way the operator will learn the functions of the device as well as
the dangers associated with its use. Proper use of equipment is the responsibility of any service
provider!

Suitable range of use
This device is designed specifically to be used with dents on flexible steel car bodies. The
diagrams below illustrate the types of dents that can be removed. Dents like the kind caused
by impact from hailstones, which leave smooth, rounded dents, can be removed. (More active
materials may call for different devices, like pull hooks or suction cups. Consult with training
personnel for specifics)

Unsuitable range of use
Sharp dents
Body areas that have been damaged and reconstructed
Crumpled/creased areas or dents along creased metal
 Aluminum bodies

Using the device
1.Connect the "**0V Power Cable" to the device's "Power Input Socket", and plug the other end of
 the cable into a **0V power socket. Flip the "ON/OFF Switch" to ON, which will turn on a red light.
 The "Work Status Display" will also turn on. This is the normal status of the device.
2.Once it turns on, the "Work Status Display" will display the WOYO logo, and will then display a
  loading message for about *0 seconds. This screen will display the work status of the device. The
  device itself will release an intermittent "beeping" sound. This is the normal status of the device.
  (Note: If the device continually displays a loading message, power it down, wait 5 minutes, then
  power it on again. If it still displays a loading message, contact one of our distributors! )
3.The "Time/effect Dial" lets you select a run time between 0.5 seconds and 4 seconds, and the
  device runs at capacity regardless of the length of time selected. Press the "Work" once to
  set run time.


Keywords:
Paintless Dent Repair
WOYO PDR***7
Paintless Dent Removal
AUTO BODY REPAIR
Heat Induction
Dent Repair
Dent Removal
Extreme Dent Removal 
WOYO Innovation
 Hail Repair Tool 
shrink over-stretching metal dent
 automatic control system
 Automotive beauty 
conservation Electronic
 Dent Repair
 Car panel Conservation 
Effective on Steel
Automotive Repair System

Electronic Soft Dent Reduction

 dent removal tool

Car Body Paint Less Dent Puller