Prix FOB
Obtenir le dernier prix|
- Minimum Order
Pays:
Saudi Arabia
N ° de modèle:
0
Prix FOB:
Localité:
ksa
Prix de commande minimale:
-
Commande minimale:
-
Packaging Detail:
-
Heure de livraison:
-
Capacité de Fournir:
-
Payment Type:
-
Groupe de produits :
-
Saudi Arabia
Personne àcontacter Mr. Mamdouh
Second Industrial City, Dammam, Other
FEATURES:
*Robust design product to meet all requirements.
*Good resistance to tear and puncture.
*Superior bonding [adhesion] with substrates and seams.
*Industrial product, heavy duty application.
SURFACE FINISH & SIZE OF ROLL
Both top& bottom covered by P.E Thin films printed also
SAND & SLATED finishes on exposed side to
protect the membrane from UV rays. The slate finish available with
various colors on customer choice. The membranes are produced
thickness 3mm, 4mm and 5mm with
the standard length *0 meter and standard width
1 meterwidely.
USES
T-ULTRAGLASS
membranes are suitable for general roofing and waterproofing
application and it can be used in single or multi-layer system.
Suitable on low slope concrete roof, balconies, multi-story car
parks, for lining sewerage canals Sub level structures and any
cement, concrete flat substrate that needs waterproofing.
Â
Â
 APPLICATION:
The waterproofing surface must be thoroughly clean and level prior
to membrane laying work at the site, And free from loose particles,
stones, steel nails, oil, grease, dust and any damaging materials
present on substrate. A coat of TAJ PRIMER is then applied to the
concrete surface at ******0 gm/m2 rate. Applied
primer should be dried well before fixing the membrane.
Membranes are fixed by torch welding called Torch on Application.
The membrane rolls are to be kept ready near the open area in which
they are going to be laid, the rolls are laid, So that next
overlaps the first membrane by *0 cm along the side lap, the
membrane is then rolled back. They are unrolled once again while
heating the underside sufficiently to surface melting. End laps
min.*5 cm. Avoid uneven torching and excessive. The lap joint area
should be heated from top to produce thin molten bitumen at the
seam, which is then smoothened with trowel ensuring properly welded
joint.
EXPOSED ROOFING:
For exposed application use TAJ MINERAL MEMBRANES. These are
produced with a top layer of natural flat slate flakes. The
membrane possess selvedge *0 cm covered by release paper or fine
sand .This is to forming lap joints end of roll joints are made by
scrapping of *5 cm of flakes.
TOOLS:
Gas cylinder and gas torch for welding, knife for trimming a trowel
with round tip, marking aids and gloves.
Â
Â
Â
Â
Â
Â
Â
Â
Â
TECHNICAL DATA T-ULTRA
GLASS
| Tests / properties | Typical values | Test method | ||||||||||||||||||||
| Thickness nominal ,mm | 3,4 & 5 |
ASTMÂ D
**1 UEAtc |
||||||||||||||||||||
| Roll length | *0 meter | Â | ||||||||||||||||||||
| Roll width | 1 meter | Â | ||||||||||||||||||||
| Penetration [mix ] @********************ong> | ****2 | ASTM D 5 | ||||||||||||||||||||
| Softening point ,deg.C | **5 | ASTM D *6 | ||||||||||||||||||||
| Water absorption [wt] % | < 1 % | ASTM D **0 | ||||||||||||||||||||
Heat resistance
Mots-clés correspondants Taj International for InsulationMots-clés correspondantsSend a direct inquiry to this supplierGet Verified Buyers & SuppliersAvail Free Consultation |
