Prix FOB
Obtenir le dernier prix( Negotiable )
|10 Carton Minimum Order
Pays:
China
N ° de modèle:
-
Prix FOB:
( Negotiable ) Obtenir le dernier prix
Localité:
-
Prix de commande minimale:
-
Commande minimale:
10 Carton
Packaging Detail:
pp BAGS(OR CARTONS)+ PALLETS
Heure de livraison:
WITHIN 25DAYS
Capacité de Fournir:
-
Payment Type:
T/T, Western Union, Other
Groupe de produits :
Personne àcontacter Mr. allen
China, Qingdao, Shandong
How to apply clips:
The correct way to attach U-bolts is shown at the right, the
U-section is in contact with the rope's dead end.
Apply the first clip one base width from dead end of wire rope, the
next clip as near the loop as possible. Space additional clips if
required equally between the first two.
Apply the initial load and retighten nuts. Rope will stretch and
shrink in diameter when loads are applied. Inspect periodically and
retighten.
IMPORTANT: Failure to make a termination in accordance with the
instructions, or failure to periodically check and retighten to the
recommended torque, will cause a reduction in efficiency rating.
Never use any wire rope clips to directly connect two straight
lengths of wire rope.
Wire Rope Clip Safety Notice!
Under the approved Code of Practice for Load Lifting &
Rigging,
slings assembled with wire rope clips are not to be used for
lifting.
To comply with manufacturer's specifications the correct number of
clips must be installed correctly and tightened to the correct
torque using a torque wrench. The correct installation technique is
shown below.
Â
When fitting clips "Don't straddle a dead horse".
A visual inspection should be carried out prior to and during
use.
Â
Wire rope clips should be inspected before use to ensure
that:
all markings are legible;
the wire rope clip is free from nicks, gouges and
cracks;
a wire rope clip with the correct dimension has been
selected;
never repair or reshape a wire rope clip by welding, heating or
bending as this may affect the performance.
The wire rope clip should be fitted to the wire rope as shown in
the diagrams below.
The bridge of the wire rope clip should always be placed on the
load bearing part of the rope. The U-bolt of
the clip should be placed on the rope tail, also known as the "dead
end" of the rope.
Turn back enough wire rope length so that the required minimum
number of clips can be installed according to the instructions
below.
The first clip must be placed one bridge width from the turned back
rope tail or dead end of the rope,
according to figure 1. Tighten nuts to the specified
torque.
The second clip must be placed immediately against the thimble but
nevertheless in such a position that the
correct tightening of the clip does not damage the outer wires of
the wire rope (figure 2). Tighten the nuts
firmly but not yet to the specified torque.
The following clips should be placed on the wire rope between the
first and second clip in such a way that
they are separated by at least 1½ times the clip-width with a
maximum of 3 times the clip-width according to figure 3.Apply light
tension on the rope and tighten all nuts evenly, alternating until
reaching the specified torque.
During assembly and before the rope is taken into service, the nuts
must be tightened once again to the
prescribed torque. After the load is applied for the first time,
the torque value must be checked again and
corrected if necessary. Periodically re-tightening of the nuts must
be done at *0.**0 cycles (heavy usage),
*0.**0 e.g. every 3 months, 6 months, annually.
The torque values and the minimum number of clips to be applied, in
relation to the rope size, are given in
the following tables.
| Pays: | China |
| N ° de modèle: | - |
| Prix FOB: | ( Negotiable ) Obtenir le dernier prix |
| Localité: | - |
| Prix de commande minimale: | - |
| Commande minimale: | 10 Carton |
| Packaging Detail: | pp BAGS(OR CARTONS)+ PALLETS |
| Heure de livraison: | WITHIN 25DAYS |
| Capacité de Fournir: | - |
| Payment Type: | T/T, Western Union, Other |
| Groupe de produits : | WIRE ROPE CLIP |
