La description
~~
Single component, self levelling, ready-to-use, high technology
fluid coating and water insulation material. It does not contain
solvent and isocyanate. It is produced with MS Polymer Hybrid
Technology and is resistant to UV. POLYMERA MS FLUID is developed
as low viscosity for horizontal surfaces. For vertical and inclined
surfaces POLYMERA MS which is a medium viscosity, semi-fluid
product, is recommended.
Properties
Technical Properties
Quality Certificates
Â
Application Areas:
•Indoor and outdoor,
•In water insulation and local repairs of horizontal surfaces,
thanks to its self levelling properties,
•In water insulation and local repair of vertical surfaces, thanks
to its ease of application with a roll or brush,
•On all kinds of mineral surfaces such as concrete, stone, marble,
ceramic, tiles, all kinds of woods, glass, all kinds of metals,
roof tile, brick, cement mixed chip panel, gas concrete etc. and
combination of all of these,
•In balconies, terrace or inclined roofs where water insulation is
required, wood and metal surfaces, in intersections of chimneys,
ventilations and skylights, and fixing the roof tiles,
•In potable water tanks, pools and cisterns,
•In repairing cracks up to 5 mm,
•In wet areas such as bathroom and kitchen,
•In places below ground level, such as foundation, garage and
basement, against water pressure and ground moisture.
Advantages:
•POLYMERA MS FLUID is MS Polymer based, which has high technical
properties, developed with Japanese technology. MS Polymer
technology has important advantages compared to existing
polyurethane, silicone, bitumen or cement acrylic based
coatings:
•Does not contain solvent and isocyanate which are harmful for
human health and for the environment. Can be safely used indoor and
in contact with the potable water. Is a **0% product.
•Is resistant to UV, does not crack or turn to yellow. Can be
safely used outdoor.
•Bonds even on damp surfaces without primer, provides high
adherence. Bonds on wet surfaces with a primer.
•Is not harmful for human health and to the environment thanks to
its low VOC values.
•Can be easily and quickly applied with brush or roll. Does not
form seams.
•Is very flexible. Can bridge the cracks up to 5 mm. Continues to
adhere, cover and protect the building from the cracks which are
formed and grow in joints of roof etc. due to the movements of the
buildings, without losing its technical properties, after being
cured. Turns to its original form perfectly.
•Protects its elasticity even in low temperatures, after being
cured. Overpaintable.
•POLYMERA MS FLUID is the only product which offers all these
advantages in a single product.
Preparation of the Surface:
•The surface must be clear of materials which prevent bonding, such
as dust, oil, tar, bitumen, paint, silicone, curing agents,
detergents and mold release oils.
•Sealants that were applied and cured in the past must be
mechanically cleaned. It should not be applied on old product which
is not completely removed.
•It is recommended to cover the boundaries of the application area
with a masking tape for the clean look of the area and prevent the
material to spread around.
Application Information:
•The tip of the cartridge is cut to place the nozzle given with the
cartridge.
•The nozzle is placed to the tip of the cartridge and cut with a
sharp craft knife with *5 degree, considering the width of the area
where it will be used, and the cartridge must be placed to the
gun.
•Following the application of the product with the gun, the surface
is smoothened with a spatula or a glove wetted with detergent. This
operation allows the silicone to bond stronger and the filling to
have a better appearance. The joint width must be between 5mm and
*0mm.
•After the application the masking tape must be removed in maximum
5 minutes.
•The product which is spread in undesired areas must be cleaned in
maximum 5 minutes with a solvent or alcohol. If this duration is
exceeded and the curing is complete, it should be cleaned
mechanically.
Consumption:
Width of the joint
 mm Depth of the joint
 mm Consumption
 ml (per 1 m) Consumption
 g (per 1 m)
5 5 *5 *3,*5
*0 *0 **0 **5
*0 *2 **0 **4
Â
Caution:
•Avoid application in temperatures below *5°C and over **0°C.
•Not suitable for use in aquariums or sealing glazed surfaces and
mirrors.
•It should not be used in completely closed areas since it needs
the humidity in the air to be cured.
•Not suitable in medical or pharmacological usages.
•It is not recommended to apply in rainy conditions.
•Not overpaintable.
Packaging:
Net **0 ml plastic cartridges
Shelf Life:
Unopened packages can be stored in a dry and cool environment
between **0°C and **5°C for *2 months, provided that the products
are protected from UV lights.
Health and Safety:
As with all chemical products, contact with food, skin, eyes and
mouth should be avoided during usage and storage. During the
application, work wears, protective gloves, goggles and mask should
be used according to the work place health regulations. If
swallowed by accident, consult a doctor. In case of contact with
skin, rinse with plenty of water. Do not leave the package open.
Avoid contact with uncured silicone for long periods of time. Keep
out of reach of children.
Â
Â
| Pays: |
Turkey |
| N ° de modèle: |
68214
|
| Prix FOB: |
(Negotiable)
Obtenir le dernier prix
|
| Localité: |
- |
| Prix de commande minimale: |
- |
| Commande minimale: |
- |
| Packaging Detail: |
1 kg , 5 kg, 14 kg |
| Heure de livraison: |
- |
| Capacité de Fournir: |
- |
| Payment Type: |
- |
| Groupe de produits : |
- |
