CE Approved Newest Small Automatic Egg Incubator YZ8-48

       CE Approved Newest Small Automatic Egg Incubator YZ***8       

I.Compared with the JN***8,Our YZ***8 have following advantages:

1. It's transparent for you to see all the process of hatching ,  also very good for children's eudcation purpose .
2. you can add water outside of the mahcine With our tool, no need you to open it  .
3. We have improved the controller, it can be in the better condition instead of the old one of JN***8.
4. We have changed the fan ,which can have lower noise when working , better for the circulation of temperature and improvement of hatching rate .
5. Temperature heating element is changed to be a new improved one . when the temperature is higher , the heater will be stopped to avoid self-ignite , It's better to keep ideal temperature inside the machine .
6. Very competitive price with high quality ,  only *0USD per pcs (instead of more than **0USD for old JN***8 on the market .)

II. Display Symbols

  III.Basic operation

1. Testing you unit for the first time:

1.1 Connect the egg turner plug to the control plug inside the egg compartment.

1.2 Connect the provided power supply to the back of the unit and your power source.

1.3 Switch on your power source.

1.4 Switch your unit on.

1.5 You will hear an alarm sounding due to low temperature/humidity.

1.6 Press any of the green s to cancel the alarm.

1.7 By opening the incubator and filling the water channels you will notice the humidity

     reading increase.

1.8 Let the unit run for 2 hours to note the egg turner turning.

2. Setting the temperature

2.1 Push “SET” once.

2.2 Push “+” or “-“ to select the desired temperature.

2.3 Push “SET” once more to exit.

- These incubators are factory set at *8oC, I found the chicks hatch at day *9 to

*0 meaning the temperature being to high. Using the method as described

above. I recommend you set the temperature at *7.6oC.

3. Temperature alarm parameter settings(AL and AH)

The temperature alarm is factory set to sound at 1oC over or below the set temperature. This is sufficient and you do not need to make any changes to these settings.

3.1 Low temperature alarm parameter setting. (AL)

3.1.1 Press and hold “SETT” for 3 sec.

3.1.2 Push “+” or “-“ until code “AL” appears in the temperature screen.

3.1.3 Push “SET”

3.1.4 Push “+” or “-“ to adjust to your desired lower alarm setting.

3.2 Higher temperature alarm parameter setting (AH)

3.2.1 Press and hold “SETT” for 3 sec.

3.2.2 Push “+” or “-“ until code “AH” appears in the temperature screen.

3.2.3 Push “SET”

3.2.4 Push “+” or “-“ to adjust to your desired higher alarm setting.

4. Humidity alarm parameter settings(AS)

The humidity alarm is factory set to sound at *5% humidity. This is sufficient and you should not deed to make any changes to these settings.

4.1 Low humidity alarm parameter setting. (AS)

4.2 Press and hold “SETT” for 3 sec.

4.3 Push “+” or “-“ until code “AS” appears in the temperature screen.

4.4 Push “SET”

4.5 Push “+” or “-“ to adjust to your desired lower alarm setting.

- By filling both water channels the humidity should rise to *0% dependant on the

local humidity levels and the time of year. I tend to fill both my water channels

every 4 to 5 days and at day *8 when I remove the egg trays I over fill them to

increase the humidity to about *5%.

IV.Package

2 pcs/big carton,

packing size is *2x*0x*3/*5kgs/2set