addition cure liquid silicone rubber raw material for mold making

Prix FOB

Obtenir le dernier prix

7.5 ~ 12 USD / Kilogram ( Negotiable )

100 Kilogram Minimum Order

Pays:

China

N Â° de modÃ¨le:

G-830 addition cure silicone rubber

Prix FOB:

7.5 ~ 12 USD / Kilogram ( Negotiable )(Negotiable) Obtenir le dernier prix

LocalitÃ©:

China

Prix de commande minimale:

7.5 per Kilogram

Commande minimale:

100 Kilogram

Packaging Detail:

20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B 25KG/drum vacuum packing f

Heure de livraison:

3 to 5 days

Capacité de Fournir:

500 Ton per Month

Payment Type:

Other, PayPal, Western Union, L/C, T/T

Groupe de produits :

addition cure silicone rubber

Contacter maintenant

Dongguan Guochuang Organic Silicone Material Co., Ltd.

China

Membre gratuit

Personne Ã contacter Ms. Sybil

NO.4 shichang street , the 2nd industrial district of xiaobian ,changan town ,dongguan China., Dongguan, Guangdong

Contacter maintenant

La description

1.Description of addition cure liquid silicone rubber
G***0 silicone rubber platinum cure silicone rubber. The silicone rubber will be cured under room temperature and can be cured fastly by heating, Its two-components liquid silicone rubber , the mixing ratio is 1:1 . It has an exceptional fluidity and good operability.Especially ,the platinum cure silicone rubber has a lower shrinkage,higher temperature resistance and it is flexible.

2.Characteristics of addition cure liquid silicone rubber
(1).An exceptional fluidity and good operability
(2).Good tensile strength and tear strength
(3).Food grade silicone rubber
(4).high temperature resistance
(5).good flexibility
(6).No smell ,non-toxic
(7).long shelf-time &lifetime
(8).Lower shrinkage

3.Application of addition cure liquid silicone rubber
G***0 silicone rubber is flexbile silicone rubber ,it has a higher temprature resistance and lower shrinkage, so it is suitable to make the silicone gasket for machine sealing .4.Datesheet of addition cure liquid silicone rubber

Item No.	Appearance	Hardness (shore A°)	Viscosity (CPS)	Tensile-strength ( kgf /cm2 )	Tear-strength (kgf /cm2 )	Elongation-break (%)	Mixing ratio	operation *time (5â„ƒ** )	*Curing time( 5 â„ƒ**)	Shrinkage
G0*	translucent	*0±2	*0±*0	≥*5	≥*4	≥**0	1:1	****0 mins	2~3 h	≤0.1%

Using instruction
1. Place a plastic container on a small scale, making sure to zero out the weight on the scale. Note: use a container that, during rise under vacuum in Step 5, will allow for material to expand to **5 times its resting volume.

2. Pour catalyst into the plastic container, noting weight of material poured.
3. In the same container, pour an equal weight of base on top of the catalyst (e.g., **0 grams of catalyst and **0 grams base). Note: within a 5% weight variance, the end result is not altered.
4. With a clean, dry mixing spatula, mix energetically until the color of the product is homogeneous. Note: working time begins at this step. Mixing should take no longer than **2 minutes.
5. Place container under vacuum and vacuum until material bubbles and rises. Release vacuum and repeat until bubbles are removed. Vacuuming should take no longer than **4 minutes.
6. From a height of approximately *0 cm, pour the mixed silicone into the mold frame. Maintain the pouring stream in the same spot so as to minimize introduction of air bubbles into the mold.
7. Allow the mold to sit, undisturbed, for at least 4 hours to ensure the silicone is fully cured.
8. Remove the mold from the frame.
9. Cut around the pattern carefully to release it from the silicone rubber mold.
Notice
The surfaces with which the material comes in contact must be perfectly clean, free of grease and dry.
Close the bottles after use so as not to confuse the cap of the catalyst with that of the base when re-sealing.
Be aware of possible cross-contamination; its highly recommended to use only dedicated gear when processing poly-addition RTV2 silicone rubber (including degassing devices).
Be aware that contact with certain material can inhibit the curing of the RTV2 poly-addition silicone rubber. Common contaminants to be avoided include:
-Natural or synthetic rubber, vulcanized with sulphur derivatives.
-Poly-condensation RTV catalyzed with metallic salts.
-PVC stabilizing agents.
-Amine cured epoxies.
-Sulphur, tin and amines derivatives.
-In case of doubt, carry out a small test by pouring the mixture onto a small area of the object.

Packaging & Shipping
Packing:
*0KG/drum vacuum packing for part A + *0KG/drum vacuum packing for part B
*5KG/drum vacuum packing for part A + *5KG/drum vacuum packing for part B
**0KG/drum packing for part A ***0KG/drum packing for part B
Why Choose Us?
1.Free Sample
2.Sample Test
3.Technical Support
4.Engineers Site Instruction
5.New products developing
6.New Market developing
7.Factory Visiting Reception
8.China visiting reception
9.China Latest silicone news
*0.Related Products Purchasing Assistance
*1.More than 8 years experience in producing liquid silicone rubber

Pays:	China
N Â° de modÃ¨le:	G-830 addition cure silicone rubber
Prix FOB:	7.5 ~ 12 / Kilogram ( Negotiable ) (Negotiable) Obtenir le dernier prix
LocalitÃ©:	China
Prix de commande minimale:	7.5 per Kilogram
Commande minimale:	100 Kilogram
Packaging Detail:	20KG/drum vacuum packing for part A + 20KG/drum vacuum packing for part B 25KG/drum vacuum packing f
Heure de livraison:	3 to 5 days
Capacité de Fournir:	500 Ton per Month
Payment Type:	Other, PayPal, Western Union, L/C, T/T
Groupe de produits :	addition cure silicone rubber